Settings
Connect to Supabase to save reports to the cloud and make them available in the Reports Dashboard. Keys are stored on this device only.
Run this SQL once in your Supabase SQL Editor to create the table:
create table public.huia_gates_inspections ( id uuid default gen_random_uuid() primary key, submitted_at timestamptz default now(), inspector text, inspection_date date, weather text, overall_rating text, general_comments text, follow_up text, gates_data jsonb, photos jsonb, signature_data text, pass_count integer, fail_count integer, na_count integer ); alter table public.huia_gates_inspections enable row level security; create policy "allow_insert" on public.huia_gates_inspections for insert with check (true); create policy "allow_select" on public.huia_gates_inspections for select using (true);
Your in-progress inspection auto-saves to this device. Clear to start fresh.
NZF Logo
NZ Facilities Ltd
Huia Gates Monthly Inspection
Auckland Council — 6 Automated Gates
1
Inspection Details
2
Gate 1: Pine Ave – Cornwallis
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
3
Gate 2: Mill Bay
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
4
Gate 3: Kaitarakihi
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
5
Gate 4: Karamatura Farm
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
6
Gate 5: Karamatura Valley
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
7
Gate 6: Fire Break Road
0 / 40
Gate Motor & Actuator
Motor housing — no damage, corrosion or water ingress
Mounting brackets and bolts secure and tight
Drive chain / belt / rack — tension and condition OK
Gearbox — oil level and seals (no leaks)
Manual release / override functioning correctly
Motor operation — smooth, no unusual noise or vibration
Drive cog / pinion — engagement and wear acceptable
Control Board
Control box enclosure — sealed, dry, no water ingress
Wiring terminations tight, no corrosion or overheating
Fuses and breakers — correct rating, no burn marks
Battery backup — voltage and condition (where fitted)
Status LEDs and indicators operating correctly
Open / close cycle test from controller — full travel
Diagnostic log / error codes reviewed and cleared
Safety Sensors
Photocell beams aligned, lenses clean
Photocell function — gate stops or reverses on beam break
Safety edge / pressure strip operational
Anti-crush / obstacle detection working
Auto-close timer functioning within set range
Warning light / beacon operational
Limit Switches
Open limit — gate stops at correct fully-open position
Close limit — gate stops at correct fully-closed position
Switch housing secure and weatherproof
Cam / dog settings tight — no drift since last visit
Limit switch wiring intact and protected
Hinges, Locks & Mounting Structure
Gate hinges lubricated, no excessive play or wear
Hinge bolts and welds — tight, no cracks
Gate frame straight — no buckling or impact damage
Bottom guide rollers (sliding) running freely
Top track / guide secure (sliding gates)
Lock mechanism functioning — manual key override works
Concrete posts / footings — no cracks or movement
Gate signage in place and legible
Power & Cabling
Mains isolator accessible, labelled and functional
Cable runs protected — no exposed conductors
Earth bonding intact
Conduit secure and weatherproof
Cable glands sealed at entry points
Solar panel (if fitted) — clean, undamaged, aligned
Solar charge controller / battery bank — condition OK
8
Sign-Off & Submission